ptrace(2) — Linux manual pages

DESCRIPTION

The ptrace() system call provides a means by which a parent process may observe and control the execution of another process, and examine and change its core image and registers. It is primarily used to implement breakpoint debugging and system call tracing.

The parent can initiate a trace by calling fork(2) and having the resulting child do a PTRACE_TRACEME, followed (typically) by an exec(3). Alternatively, the parent may commence trace of an existing process using PTRACE_ATTACH.

While being traced, the child will stop each time a signal is delivered, even if the signal is being ignored. (The exception is SIGKILL, which has its usual effect.) The parent will be notified at its next wait(2) and may inspect and modify the child process while it is stopped. The parent then causes the child to continue, optionally ignoring the delivered signal (or even delivering a different signal instead).

When the parent is finished tracing, it can terminate the child with PTRACE_KILL or cause it to continue executing in a normal, untraced mode via PTRACE_DETACH.

The value of request determines the action to be performed:

PTRACE_TRACEME: Indicates that this process is to be traced by its parent. Any signal (except SIGKILL) delivered to this process will cause it to stop and its parent to be notified via wait(2). Also, all subsequent calls to execve(2) by this process will cause a SIGTRAP to be sent to it, giving the parent a chance to gain control before the new program begins execution. A process probably shouldn't make this request if its parent isn't expecting to trace it. (pid, addr, and data are ignored.)

The above request is used only by the child process; the rest are used only by the parent. In the following requests, pid specifies the child process to be acted on. For requests other than PTRACE_KILL, the child process must be stopped.

PTRACE_PEEKTEXT, PTRACE_PEEKDATA

Reads a word at the location addr in the child's memory, returning the word as the result of the ptrace() call. Linux does not have separate text and data address spaces, so the two requests are currently equivalent. (The argument data is ignored.)

PTRACE_PEEKUSR

Reads a word at offset addr in the child's USER area, which holds the registers and other information about the process (see <linux/user.h> and <sys/user.h>). The word is returned as the result of the ptrace() call. Typically the offset must be word-aligned, though this might vary by architecture. (data is ignored.)

PTRACE_POKETEXT, PTRACE_POKEDATA

Copies the word data to location addr in the child's memory. As above, the two requests are currently equivalent.

PTRACE_POKEUSR

Copies the word data to offset addr in the child's USER area. As above, the offset must typically be word-aligned. In order to maintain the integrity of the kernel, some modifications to the USER area are disallowed.

PTRACE_GETREGS, PTRACE_GETFPREGS

Copies the child's general purpose or floating-point registers, respectively, to location data in the parent. See <linux/user.h> for information on the format of this data. (addr is ignored.)

PTRACE_GETSIGINFO (since Linux 2.3.99-pre6)

Retrieve information about the signal that caused the stop. Copies a siginfo_t structure (see sigaction(2)) from the child to location data in the parent. (addr is ignored.)

PTRACE_SETREGS, PTRACE_SETFPREGS

Copies the child's general purpose or floating-point registers, respectively, from location data in the parent. As for PTRACE_POKEUSER, some general purpose register modifications may be disallowed. (addr is ignored.)

PTRACE_SETSIGINFO (since Linux 2.3.99-pre6)

Set signal information. Copies a siginfo_t structure from location data in the parent to the child. This will only affect signals that would normally be delivered to the child and were caught by the tracer. It may be difficult to tell these normal signals from synthetic signals generated by ptrace() itself. (addr is ignored.)

PTRACE_SETOPTIONS (since Linux 2.4.6; see BUGS for caveats)

Sets ptrace options from data in the parent. (addr is ignored.) data is interpreted as a bitmask of options, which are specified by the following flags:

PTRACE_O_TRACESYSGOOD (since Linux 2.4.6)

When delivering syscall traps, set bit 7 in the signal number (i.e., deliver (SIGTRAP | 0x80) This makes it easy for the tracer to tell the difference between normal traps and those caused by a syscall. (PTRACE_O_TRACESYSGOOD may not work on all architectures.)

PTRACE_O_TRACEFORK (since Linux 2.5.46)

Stop the child at the next fork(2) call with SIGTRAP | PTRACE_EVENT_FORK << 8 and automatically start tracing the newly forked process, which will start with a SIGSTOP. The PID for the new process can be retrieved with PTRACE_GETEVENTMSG.

PTRACE_O_TRACEVFORK (since Linux 2.5.46)

Stop the child at the next vfork(2) call with SIGTRAP | PTRACE_EVENT_VFORK << 8 and automatically start tracing the newly vforked process, which will start with a SIGSTOP. The PID for the new process can be retrieved with PTRACE_GETEVENTMSG.

PTRACE_O_TRACECLONE (since Linux 2.5.46)

Stop the child at the next clone(2) call with SIGTRAP | PTRACE_EVENT_CLONE << 8 and automatically start tracing the newly cloned process, which will start with a SIGSTOP. The PID for the new process can be retrieved with PTRACE_GETEVENTMSG. This option may not catch clone(2) calls in all cases. If the child calls clone(2) with the CLONE_VFORK flag, PTRACE_EVENT_VFORK will be delivered instead if PTRACE_O_TRACEVFORK is set; otherwise if the child calls clone(2) with the exit signal set to SIGCHLD, PTRACE_EVENT_FORK will be delivered if PTRACE_O_TRACEFORK is set.

PTRACE_O_TRACEEXEC (since Linux 2.5.46)

Stop the child at the next execve(2) call with SIGTRAP | PTRACE_EVENT_EXEC << 8.

PTRACE_O_TRACEVFORKDONE (since Linux 2.5.60)

Stop the child at the completion of the next vfork(2) call with SIGTRAP | PTRACE_EVENT_VFORK_DONE << 8.

PTRACE_O_TRACEEXIT (since Linux 2.5.60)

Stop the child at exit with SIGTRAP | PTRACE_EVENT_EXIT << 8. The child's exit status can be retrieved with PTRACE_GETEVENTMSG. This stop will be done early during process exit when registers are still available, allowing the tracer to see where the exit occurred, whereas the normal exit notification is done after the process is finished exiting. Even though context is available, the tracer cannot prevent the exit from happening at this point.

PTRACE_GETEVENTMSG (since Linux 2.5.46)

Retrieve a message (as an unsigned long) about the ptrace event that just happened, placing it in the location data in the parent. For PTRACE_EVENT_EXIT this is the child's exit status. For PTRACE_EVENT_FORK, PTRACE_EVENT_VFORK and PTRACE_EVENT_CLONE this is the PID of the new process. Since Linux 2.6.18, the PID of the new process is also available for PTRACE_EVENT_VFORK_DONE. (addr is ignored.)

PTRACE_CONT

Restarts the stopped child process. If data is non-zero and not SIGSTOP, it is interpreted as a signal to be delivered to the child; otherwise, no signal is delivered. Thus, for example, the parent can control whether a signal sent to the child is delivered or not. (addr is ignored.)

PTRACE_SYSCALL, PTRACE_SINGLESTEP

Restarts the stopped child as for PTRACE_CONT, but arranges for the child to be stopped at the next entry to or exit from a system call, or after execution of a single instruction, respectively. (The child will also, as usual, be stopped upon receipt of a signal.) From the parent's perspective, the child will appear to have been stopped by receipt of a SIGTRAP. So, for PTRACE_SYSCALL, for example, the idea is to inspect the arguments to the system call at the first stop, then do another PTRACE_SYSCALL and inspect the return value of the system call at the second stop. (addr is ignored.)

PTRACE_SYSEMU, PTRACE_SYSEMU_SINGLESTEP (since Linux 2.6.14)

For PTRACE_SYSEMU, continue and stop on entry to the next syscall, which will not be executed. For PTRACE_SYSEMU_SINGLESTEP, do the same but also singlestep if not a syscall. This call is used by programs like User Mode Linux that want to emulate all the child's system calls. (addr and data are ignored; not supported on all architectures.)

PTRACE_KILL

Sends the child a SIGKILL to terminate it. (addr and data are ignored.)

PTRACE_ATTACH

Attaches to the process specified in pid, making it a traced "child" of the current process; the behavior of the child is as if it had done a PTRACE_TRACEME. The current process actually becomes the parent of the child process for most purposes (e.g., it will receive notification of child events and appears in ps(1) output as the child's parent), but a getppid(2) by the child will still return the PID of the original parent. The child is sent a SIGSTOP, but will not necessarily have stopped by the completion of this call; use wait(2) to wait for the child to stop. (addr and data are ignored.)

PTRACE_DETACH

Restarts the stopped child as for PTRACE_CONT, but first detaches from the process, undoing the reparenting effect of PTRACE_ATTACH, and the effects of PTRACE_TRACEME. Although perhaps not intended, under Linux a traced child can be detached in this way regardless of which method was used to initiate tracing. (addr is ignored.)

RETURN VALUE

On success, PTRACE_PEEK* requests return the requested data, while other requests return zero. On error, all requests return −1, and errno is set appropriately. Since the value returned by a successful PTRACE_PEEK* request may be −1, the caller must check errno after such requests to determine whether or not an error occurred.

ERRORS

EBUSY: (i386 only) There was an error with allocating or freeing a debug register.
EFAULT: There was an attempt to read from or write to an invalid area in the parent's or child's memory, probably because the area wasn't mapped or accessible. Unfortunately, under Linux, different variations of this fault will return EIO or EFAULT more or less arbitrarily.
EINVAL: An attempt was made to set an invalid option.
EIO: request is invalid, or an attempt was made to read from or write to an invalid area in the parent's or child's memory, or there was a word-alignment violation, or an invalid signal was specified during a restart request.
EPERM: The specified process cannot be traced. This could be because the parent has insufficient privileges (the required capability is CAP_SYS_PTRACE); non-root processes cannot trace processes that they cannot send signals to or those running set-user-ID/set-group-ID programs, for obvious reasons. Alternatively, the process may already be being traced, or be init (PID 1).
ESRCH: The specified process does not exist, or is not currently being traced by the caller, or is not stopped (for requests that require that).

CONFORMING TO

SVr4, 4.3BSD

NOTES

Although arguments to ptrace() are interpreted according to the prototype given, GNU libc currently declares ptrace() as a variadic function with only the request argument fixed. This means that unneeded trailing arguments may be omitted, though doing so makes use of undocumented gcc(1) behavior.

init(8), the process with PID 1, may not be traced.

The layout of the contents of memory and the USER area are quite OS- and architecture-specific.

The size of a "word" is determined by the OS variant (e.g., for 32-bit Linux it is 32 bits, etc.).

Tracing causes a few subtle differences in the semantics of traced processes. For example, if a process is attached to with PTRACE_ATTACH, its original parent can no longer receive notification via wait(2) when it stops, and there is no way for the new parent to effectively simulate this notification.

When the parent receives an event with PTRACE_EVENT_* set, the child is not in the normal signal delivery path. This means the parent cannot do ptrace(PTRACE_CONT) with a signal or ptrace(PTRACE_KILL). kill(2) with a SIGKILL signal can be used instead to kill the child process after receiving one of these messages.

This page documents the way the ptrace() call works currently in Linux. Its behavior differs noticeably on other flavors of Unix. In any case, use of ptrace() is highly OS- and architecture-specific.

The SunOS man page describes ptrace() as "unique and arcane", which it is. The proc-based debugging interface present in Solaris 2 implements a superset of ptrace() functionality in a more powerful and uniform way.

BUGS

On hosts with 2.6 kernel headers, PTRACE_SETOPTIONS is declared with a different value than the one for 2.4. This leads to applications compiled with such headers failing when run on 2.4 kernels. This can be worked around by redefining PTRACE_SETOPTIONS to PTRACE_OLDSETOPTIONS, if that is defined.

Name

Synopsis